How To Put Jeep Liberty In 4 Wheel Drive
Once the shifter is in 4low, disconnect the linkage at the transfer case, removing the flat linkage bar that's attached to the transfer case with a 9/16 nut. Stop your jeep and put the gear shift selector in n (neutral).
To do this, press the button or shift lever on your liberty that reads “4h” or “hi”.
How to put jeep liberty in 4 wheel drive. Read about the 2002 jeep liberty and some applications for the jeep liberty off road. Returning back into 2lo (off position) is reverse, tranny into n at slow speed, forward push down on transfer case shifter, part time light goes off. Pull up 1 notch on the transfer case which will put you into 4 hi and part time light will show on dash, return the transmission back into drive.
I tried while in park, neuteral and moving at under 5. I did not worry about it because it worked in both four and two. Move the gear selector back to d (drive) and continue driving.
Using the point of a ballpoint pen or similar object, press and hold the recessed transfer case neutral (n) button (located above the selector switch) for four seconds, until the light behind the neutral (n) symbol starts to blink, indicating shift in progress. You are now locked in 4 hi speed up to 55mph ok. Move the 4wd shift selector straight down to 4h (from 2h).
Keep your foot applied to the brake pedal. Clutch feels good, clutch hydraulic has fluid in it.about 2 miles from home stopped at light t. I bought my 2005 jeep liberty, last year and the part time light was on in two wheel drive instead of four wheel.
Less than 1 hour to correct both problems. How do i put my 2007 jeep liberty in 4 wheel drive? Put your jeep back into gear and you're good to go.tips, tricks, dos and don'ts:
I started the jeep, warmed it up, and put it into 4 wheel low. Also added, adjusting the gear shift lever. Engage four wheel drive jeep liberty to engage four wheel drive pull up on the handle in the center console with the letters, 2h, 4h, n, 4l.
Jeep stuck in low four wheel drive. This sensor is actually a strip that has several resistive strips on it.as the strip travels from say 4 wheel part time to 2 wheel drive a different resistive strip travels between two metal contacts to advise the bcm, ecm etc. How do you shift a 4 wheel drive in a jeep liberty?
The case will shift easier if you ease off the throttle as you move the lever. How to change the shift interlock cable and remove ignition key. Can't shift jeep in to 4 wheel drive.
I can shift it in four wheel drive and it feels normal with no noise but it is still only in. Shift you transmission to neutral then grasp the transfer case shifter. It was a beautiful thing until i tried putting it back on 2 wheel drive.
Hello, i was driving my 2012 jeep liberty this morning, we are having a snow storm here in denver. Shifting from 4l to 2 wheel problem i have a jk 2010 unlimited which i purchased feb 15 2013 and the next day i put it in 4 wheel drive to climb a three ft. If that doesn't work, drive forward, and again do the above, trans.
Slow the truck down to 2 or 3 mph, and then shift the transmission into neutral. I think it's best to shift the jeep into 4low and adjust the linkage there. The first thing you need to do is select the low range.
With your jeep still rolling, shift into neutral and slowly and firmly pull the lever all the way back. This is the general way to shift into 4x4 in this model of wrangler. This year the light went completely out and four wheel drive no longer works.
Put it in gear with the motor off then with the clutch in tried to start it and it wanted to take off!! Put the transmission in neutral, emergency brake off, foot off the brake pedal, now try shifting out of 4 wheel drive low.
Belum ada Komentar untuk "How To Put Jeep Liberty In 4 Wheel Drive"
Posting Komentar